Tuesday, April 23, 2013

E- Reader Cover Sewing Pattern, Kindle Cover Tutorial, How to Sew Fabric Cover for E- Readers

Dress up your e-reader in this cute fabric cover.This sewing pattern will help you make an  e-reader cover, which is a perfect replacement for any store-bought one. This padded cover helps to keep your e-reader free from dust, dirt and scratches. When you are not reading, the inner pocket offers the perfect storage solution for your e-reader and the Velcro strap ensures perfect safety from falling off during travel.

This tutorial provides measurements to sew fabric covers for various e-readers like Kindle Fire, Kindle Keyboard, Kindle 3G, Kindle Touch and Sony Pocket.

Materials Required

1) Cotton Fabric - 1/4 yard

2) Medium weight fusible interfacing- 1/4 yard

3) Batting (optionally, you can use felt, here I have used so)- 1/4 yard

4) Velcro

5) Sewing Notions


The table below give the measurements for the main piece, pocket piece and interfacing for various e-readers. Note that "L" stands for the length of the fabric and "W" stands for the width of the fabric cut.

*Note: The seam allowance is 3/8-inch throughout.

Cut the fabric pieces for the main piece, pocket piece, main interfacing, pocket interfacing, main batting and pocket batting, referring to the table above. Note that the batting pieces are of the same measurements as the interfacing pieces.

Take the pocket piece and the pocket interfacing and fuse the interfacing onto the wrong side of the fabric following manufacturers instructions. Note that you have to leave 3/8 -inch space all around while fusing.

Lets do the triangular corner pieces that would hold the e-reader in place while reading.

Cut four fabric squares and two interfacing of 3" x 3" dimension.

Take two of the above mentioned squares and fuse the interfacing onto the wrong side. Cut the two fused squares along the diagonal to get four equal sized triangles as shown above. Cut the other two fabric squares also to get four fabric triangles.

Take a fused triangle and a plane one, layer them with the right sides together and aligning the edges. Sew along the longer edge as marked above. 


Turn over to the right side and press. Topstitch along the longer side to make the triangle neat and crisp. Clip the protruding corners. Repeat the steps with the other triangles to get the four corner pieces of the pocket.

Pin the four triangles onto the four corners of the pocket, on the  right side, aligning the edges. Sew the triangles onto the pocket, removing the pins as you go.

Take the other pocket piece (not fused with interfacing) and keep it over the done pocket piece, with the right sides together and aligning the edges. Sew along one of the longer edge, as marked above. Turn over to the right side and press. Top stitch along the seam line of the two pieces to make it neat and crisp.

Sew the two raw edges together on the right side as marked above to keep it in place. 

Now we need to insert the batting. The two shorter sides of the pocket are left open.

Take the batting for the pocket and insert it through one of the opening till it reaches the other end, keeping it straight and without wrinkles, as you go. 

Now we need to attach the pocket onto the main piece of the cover.

Take the main fabric piece and the interfacing and fuse the interfacing onto the wrong edge of the fabric, leaving a 3/8 -inch space all around, as shown above.

Fold one of the shorter edge of the main piece by 3/8 -inch and press.

Now take the done pocket and keep it on the right side of the main body of the cover, aligning the raw edges and with the finished side of the pocket along the center as shown above and pin. Sew the pocket onto the main body along the black line as marked in the picture.

Now we need to add the strap and the velcro for closure.

Take a piece of fabric, 4 & 1/2-inches long and 3 & 1/2- inches wide. Fold it in half lengthwise and sew along the marked line above.

Turn it inside out, press taut and top stitch around the edges to make it look neater. Now take the velcro piece, of about 1" x 1" dimension and place it at a distance of 2& 1/2-inches from the raw edge of the strap. Secure the Velcro piece by sewing around its edges.

Lets attach the strap and the corresponding velcro piece onto the other main cover piece (without pockets and interfacing).

Take the other piece meant for the main body, fold one of its shorter edges inwards by 3/8-inch and press.

Now keep the piece on its right side and mark the center of the two of its shorter edges.Place the  Velcro piece 2 -inches from the folded shorter edge of the fabric piece and sew around its edges to secure. Now place the strap at the marked point on the other side in such a way that the Velcro is exposed and secure it by sewing along its shorter edge.

Take the two main body pieces, layer them with the right sides together and aligning the edges (the folded edges of the two pieces should come together) and sew along the marked line as shown above. The folded shorter edge is left open to insert the batting.

Turn the cover inside-out. Poke out the corners with the tip of your scissors and press taught .

Take the batting with the required dimension and insert it through the opening till the other shorter edge as shown above. 

Sew the opening shut along the marked line (blue).

Your e-reader cover is ready in less than an hour!